ASDA Soft V4.08.09 DELTA Servo Software ASDA Soft V4.08.09 is the software used to configure the old DELTA Servo’s including models: ASDA-A / A+ /AB / B / A2 / B2 series
Mitsubishi USB-QC30R2 programming cable is emulated into a traditional serial port (commonly known as COM port) through the USB port of the computer, so that the existing various programming software, communication software and monitoring software are used. This cable is suitable for Mitsubishi Q series PLC
QC30R2 Cable Pinout
qc30r2 cable diagram
How to use USB-QC30R2
USB-QC30R2 programming cable requires a USB driver to be installed (usb qc30r2 driver download)
After the driver installation is completed, the COM port corresponding to the USB-QC30R2 programming cable will appear in the Windows device manager. Just select the COM port in the programming software, which is exactly the same as the serial programming cable QC30R2.
When using, first insert the cable into the USB port of the computer, and then insert the 6-pin round port into the Q PLC
Open-Explorer-View COM slogan by clicking with the mouse-My Computer-Control Panel-Administrative Tools-Computer Management-Device Manager-Port (COM and PT) -Prolific USB-to-SerialComm (COMx) This COMx is the COM port used by the USB programming cable
Open the programming software GX DEVELOPER, open-online-transmission settings-and double-click-serial port (USB)-set the COM port, and set the baud rate to 9600BPS to communicate
Difference between Mitsubishi PLC programming cable USB-SC09 and USWhat is the difference between Mitsubishi PLC programming cable USB-SC09 and USB-SC09-FX
USB-SC09-FX is only used for Mitsubishi FX series, USB-SC09 is generally used for Mitsubishi FX series and A series
And FX-USB-AW is for Mitsubishi FX3U 3G 1N 2N 1S Series PLC Programming Cable Replaced by USB-SC09-FX
Mitsubishi plc pin interface diagram
sc09 programming cable diagram
sc09 programming cable diagram
How to use usb-sc09 cable?
The USB-SC09 programming cable requires a USB device driver to be used. After the driver installation is complete, the COM port corresponding to the USB-SC09 programming cable will appear in the Windows device manager. Just select the COM port in the programming software or other application software. Other communication parameters use the default settings. The next use is the same as the traditional RS232 port programming cable. A Note: DB25M plug and MD8M plug at the RS422 end cannot be used at the same time.
PC adapter USB A2 USB adapter (USB V2.0) for connection of a PG/PC or notebook to SIMATIC S7 via PROFIBUS or MPI contain USB cable 5 m, MPI cable 0.3 m can be used under Windows XP/Vista/ Windows 7 32/64-bit and higher
This is the latest step-by-step instructions for installing a USB to serial cable and identifying and changing the COM port number. This applies to all Windows operating systems.
This is the latest step-by-step instructions for PLC data cable driver CH340 DRIVER, FTDI DRIVER, installing USB to serial cable, and identifying and changing COM port number.
This applies to all Windows operating systems.
The following procedure applies to all our cables, including Mitsubishi usb-sc09 usb-qc30r2, Delta usbacab230, Allen Bradley usb-1761-CBL-PM02, usb-1747-CP3, and usb-2711-NC13, etc.
To begin, find the driver suitable for the plc data line. If the steps are clear, you can view it here.
Economic version CH340 install
High speed version FT232
When you are done, open the “Device Manager” and the USB to serial adapter displays
1, TSXPCX3030-C is the TSXPCX3030-C cable driver, please install it first.
2. When programming the Twido series PLC with the TSXPCX3030-C cable, in addition to installing the programming software, you need to install the Modbus driver. The Modbus driver version cannot be lower than 1.1.
3. When the user uses the PL7 software to program the Micro or Premium series PLC, the Uni-telway driver needs to be installed. The Uni-telway driver cannot be lower than 1.6.